Find the best tutors and institutes for Class 11 Tuition
Q9.5:
A (50\text{ kg}) girl wearing high heel shoes balances on a single heel. The heel is circular with a diameter (1.0\text{ cm}). What is the pressure exerted by the heel on the horizontal floor ?
Solution :
Given Variables & Initial Setup
To determine the pressure exerted by the heel on the floor, we identify the following parameters provided in the problem statement:
- Mass of the girl ($m$) = $50 \text{ kg}$
- Diameter of the circular heel ($d$) = $1.0 \text{ cm} = 1.0 \times 10^{-2} \text{ m}$
- Acceleration due to gravity ($g$) = $9.8 \text{ m/s}^2$
Step 1: Calculating the Force Exerted
The force ($F$) exerted on the floor is equal to the weight of the girl acting on the single heel. [Per Newton's Second Law of Motion, $F = mg$]
$F = 50 \text{ kg} \times 9.8 \text{ m/s}^2$
$F = 490 \text{ N}$
Step 2: Calculating the Area of the Heel
The heel is circular. The area ($A$) of a circle is given by $A = \pi r^2$. First, we find the radius ($r$):
$r = \frac{d}{2} = \frac{1.0 \times 10^{-2} \text{ m}}{2} = 0.5 \times 10^{-2} \text{ m} = 5 \times 10^{-3} \text{ m}$
Now, calculate the area:
$A = \pi \times (5 \times 10^{-3} \text{ m})^2$
$A = 3.14 \times 25 \times 10^{-6} \text{ m}^2$
$A = 78.5 \times 10^{-6} \text{ m}^2 = 7.85 \times 10^{-5} \text{ m}^2$
Step 3: Calculating the Pressure
Pressure ($P$) is defined as the force acting per unit area. [Per the fundamental definition of Pressure, $P = \frac{F}{A}$]
$P = \frac{490 \text{ N}}{7.85 \times 10^{-5} \text{ m}^2}$
$P \approx 6.242 \times 10^{6} \text{ Pa}$
Visual Representation of Force Distribution
Conversion to Standard Engineering Units
| Metric Unit | Result |
|---|---|
| Pascals (Pa) | $6.24 \times 10^{6} \text{ Pa}$ |
| MegaPascals (MPa) | $6.24 \text{ MPa}$ |
Final Solution: The pressure exerted by the heel on the floor is $6.24 \times 10^{6} \text{ Pa}$ (or $6.24 \text{ MPa}$).
More Questions from Class 11 Physics Mechanical Properties of Fluids EXERCISES
- Q9.1(a): Explain why (a) The blood pressure in humans is greater at the feet than at the brain
- Q9.1(b): Explain why (b) Atmospheric pressure at a height of about (6\text{ km}) decreases to nearly half of its value at the sea level, though the height of the atmosphere is more than (100\text{ km})
- Q9.1(c): Explain why (c) Hydrostatic pressure is a scalar quantity even though pressure is force divided by area.
- Q9.10: If (15.0\text{ cm}) of water and spirit each are further poured into the respective arms of the tube, what is the difference in the levels of mercury in the two arms ? (Specific gravity of mercury = (13.6))
- Q9.11: Can Bernoulli’s equation be used to describe the flow of water through a rapid in a river ? Explain.
- Q9.12: Does it matter if one uses gauge instead of absolute pressures in applying Bernoulli’s equation ? Explain.
- Q9.13: Glycerine flows steadily through a horizontal tube of length (1.5\text{ m}) and radius (1.0\text{ cm}). If the amount of glycerine collected per second at one end is (4.0 \times 10^{-3}\text{ kg s}^{-1}), what is the pressure difference between the two ends of the tube ? (Density of glycerine = (1.3 \times 10^{3}\text{ kg m}^{-3}) and viscosity of glycerine = (0.83\text{ Pa s})). [You may also like to check if the assumption of laminar flow in the tube is correct].
- Q9.14: In a test experiment on a model aeroplane in a wind tunnel, the flow speeds on the upper and lower surfaces of the wing are (70\text{ m s}^{-1})and (63\text{ m s}^{-1}) respectively. What is the lift on the wing if its area is (2.5\text{ m}^{2}) ? Take the density of air to be (1.3\text{ kg m}^{-3}).
- Q9.15: Figures 9.20(a) and (b) refer to the steady flow of a (non-viscous) liquid. Which of the two figures is incorrect ? Why ?
- Q9.16: The cylindrical tube of a spray pump has a cross-section of (8.0\text{ cm}^{2}) one end of which has (40) fine holes each of diameter (1.0\text{ mm}). If the liquid flow inside the tube is (1.5\text{ m min}^{-1}), what is the speed of ejection of the liquid through the holes ?
- Q9.17: A U-shaped wire is dipped in a soap solution, and removed. The thin soap film formed between the wire and the light slider supports a weight of (1.5 \times 10^{-2}\text{ N}) (which includes the small weight of the slider). The length of the slider is (30\text{ cm}). What is the surface tension of the film ?
- Q9.18: Figure 9.21 (a) shows a thin liquid film supporting a small weight = (4.5 \times 10^{-2}\text{ N}). What is the weight supported by a film of the same liquid at the same temperature in Fig. (b) and (c) ? Explain your answer physically.
- Q9.19: What is the pressure inside the drop of mercury of radius (3.00\text{ mm}) at room temperature ? Surface tension of mercury at that temperature ((20^{\circ}\text{C})) is (4.65 \times 10^{-1}\text{ N m}^{-1}). The atmospheric pressure is (1.01 \times 10^{5}\text{ Pa}). Also give the excess pressure inside the drop.
- Q9.2(a): Explain why (a) The angle of contact of mercury with glass is obtuse, while that of water with glass is acute.
- Q9.2(b): Explain why (b) Water on a clean glass surface tends to spread out while mercury on the same surface tends to form drops. (Put differently, water wets glass while mercury does not.)
- Q9.2(c): Explain why (c) Surface tension of a liquid is independent of the area of the surface
- Q9.2(d): Explain why (d) Water with detergent disolved in it should have small angles of contact.
- Q9.2(e): Explain why (e) A drop of liquid under no external forces is always spherical in shape
- Q9.20: What is the excess pressure inside a bubble of soap solution of radius (5.00\text{ mm}), given that the surface tension of soap solution at the temperature ((20^{\circ}\text{C})) is (2.50 \times 10^{-2}\text{ N m}^{-1}) ? If an air bubble of the same dimension were formed at depth of (40.0\text{ cm}) inside a container containing the soap solution (of relative density (1.20)), what would be the pressure inside the bubble ? (1 atmospheric pressure is (1.01 \times 10^{5}\text{ Pa})).
- Q9.3(a): Fill in the blanks using the word(s) from the list appended with each statement: (a) Surface tension of liquids generally . . . with temperatures (increases / decreases)
- Q9.3(b): Fill in the blanks using the word(s) from the list appended with each statement: (b) Viscosity of gases . . . with temperature, whereas viscosity of liquids . . . with temperature (increases / decreases)
- Q9.3(c): Fill in the blanks using the word(s) from the list appended with each statement: (c) For solids with elastic modulus of rigidity, the shearing force is proportional to . . . , while for fluids it is proportional to . . . (shear strain / rate of shear strain)
- Q9.3(d): Fill in the blanks using the word(s) from the list appended with each statement: (d) For a fluid in a steady flow, the increase in flow speed at a constriction follows (conservation of mass / Bernoulli’s principle)
- Q9.3(e): Fill in the blanks using the word(s) from the list appended with each statement: (e) For the model of a plane in a wind tunnel, turbulence occurs at a ... speed for turbulence for an actual plane (greater / smaller)
- Q9.4(a): Explain why (a) To keep a piece of paper horizontal, you should blow over, not under, it
- Q9.4(b): Explain why (b) When we try to close a water tap with our fingers, fast jets of water gush through the openings between our fingers
- Q9.4(c): Explain why (c) The size of the needle of a syringe controls flow rate better than the thumb pressure exerted by a doctor while administering an injection
- Q9.4(d): Explain why (d) A fluid flowing out of a small hole in a vessel results in a backward thrust on the vessel
- Q9.4(e): Explain why (e) A spinning cricket ball in air does not follow a parabolic trajectory
- Q9.6: Toricelli’s barometer used mercury. Pascal duplicated it using French wine of density (984\text{ kg m}^{-3}). Determine the height of the wine column for normal atmospheric pressure.
- Q9.7: A vertical off-shore structure is built to withstand a maximum stress of (10^{9}\text{ Pa}). Is the structure suitable for putting up on top of an oil well in the ocean ? Take the depth of the ocean to be roughly (3\text{ km}), and ignore ocean currents.
- Q9.8: A hydraulic automobile lift is designed to lift cars with a maximum mass of (3000\text{ kg}). The area of cross-section of the piston carrying the load is (425\text{ cm}^{2}). What maximum pressure would the smaller piston have to bear ?
- Q9.9: A U-tube contains water and methylated spirit separated by mercury. The mercury columns in the two arms are in level with (10.0\text{ cm}) of water in one arm and (12.5\text{ cm}) of spirit in the other. What is the specific gravity of spirit ?
- Q10.1(a): Explain why (a) The blood pressure in humans is greater at the feet than at the brain
- Q10.1(b): Explain why (b) Atmospheric pressure at a height of about 6 km decreases to nearly half of its value at the sea level, though the height of the atmosphere is more than 100 km
- Q10.1(c): Explain why (c) Hydrostatic pressure is a scalar quantity even though pressure is force divided by area.
- Q10.10: In the previous problem, if 15.0 cm of water and spirit each are further poured into the respective arms of the tube, what is the difference in the levels of mercury in the two arms ? (Specific gravity of mercury = 13.6)
- Q10.11: Can Bernoulli’s equation be used to describe the flow of water through a rapid in a river ? Explain.
- Q10.12: Does it matter if one uses gauge instead of absolute pressures in applying Bernoulli’s equation ? Explain.
- Q10.13: Glycerine flows steadily through a horizontal tube of length 1.5 m and radius 1.0 cm. If the amount of glycerine collected per second at one end is $4.0 \times 10^{-3} kg s^{-1}$, what is the pressure difference between the two ends of the tube ? (Density of glycerine = $1.3 \times 10^3 kg m^{-3}$ and viscosity of glycerine = $0.83 Pa s$). [You may also like to check if the assumption of laminar flow in the tube is correct].
- Q10.14: In a test experiment on a model aeroplane in a wind tunnel, the flow speeds on the upper and lower surfaces of the wing are $70 m s^{-1}$ and $63 m s^{-1}$ respectively. What is the lift on the wing if its area is $2.5 m^2$ ? Take the density of air to be $1.3 kg m^{-3}$.
- Q10.15: Figures 10.23(a) and (b) refer to the steady flow of a (non-viscous) liquid. Which of the two figures is incorrect ? Why ?
- Q10.16: The cylindrical tube of a spray pump has a cross-section of $8.0 cm^2$ one end of which has 40 fine holes each of diameter 1.0 mm. If the liquid flow inside the tube is $1.5 m min^{-1}$, what is the speed of ejection of the liquid through the holes ?
- Q10.17: A U-shaped wire is dipped in a soap solution, and removed. The thin soap film formed between the wire and the light slider supports a weight of $1.5 \times 10^{-2} N$ (which includes the small weight of the slider). The length of the slider is 30 cm. What is the surface tension of the film ?
- Q10.18: Figure 10.24 (a) shows a thin liquid film supporting a small weight = $4.5 \times 10^{-2} N$. What is the weight supported by a film of the same liquid at the same temperature in Fig. (b) and (c) ? Explain your answer physically.
- Q10.19: What is the pressure inside the drop of mercury of radius 3.00 mm at room temperature ? Surface tension of mercury at that temperature (20 °C) is $4.65 \times 10^{-1} N m^{-1}$. The atmospheric pressure is $1.01 \times 10^5 Pa$. Also give the excess pressure inside the drop.
- Q10.2(a): Explain why (a) The angle of contact of mercury with glass is obtuse, while that of water with glass is acute.
- Q10.2(b): Explain why (b) Water on a clean glass surface tends to spread out while mercury on the same surface tends to form drops. (Put differently, water wets glass while mercury does not.)
- Q10.2(c): Explain why (c) Surface tension of a liquid is independent of the area of the surface
- Q10.2(d): Explain why (d) Water with detergent disolved in it should have small angles of contact.
- Q10.2(e): Explain why (e) A drop of liquid under no external forces is always spherical in shape
- Q10.20: What is the excess pressure inside a bubble of soap solution of radius 5.00 mm, given that the surface tension of soap solution at the temperature (20 °C) is $2.50 \times 10^{-2} N m^{-1}$ ? If an air bubble of the same dimension were formed at depth of 40.0 cm inside a container containing the soap solution (of relative density 1.20), what would be the pressure inside the bubble ? (1 atmospheric pressure is $1.01 \times 10^5 Pa$).
- Q10.3(a): Fill in the blanks using the word(s) from the list appended with each statement: (a) Surface tension of liquids generally . . . with temperatures (increases / decreases)
- Q10.3(b): Fill in the blanks using the word(s) from the list appended with each statement: (b) Viscosity of gases . . . with temperature, whereas viscosity of liquids . . . with temperature (increases / decreases)
- Q10.3(c): Fill in the blanks using the word(s) from the list appended with each statement: (c) For solids with elastic modulus of rigidity, the shearing force is proportional to . . . , while for fluids it is proportional to . . . (shear strain / rate of shear strain)
- Q10.3(d): Fill in the blanks using the word(s) from the list appended with each statement: (d) For a fluid in a steady flow, the increase in flow speed at a constriction follows (conservation of mass / Bernoulli’s principle)
- Q10.3(e): Fill in the blanks using the word(s) from the list appended with each statement: (e) For the model of a plane in a wind tunnel, turbulence occurs at a ... speed for turbulence for an actual plane (greater / smaller)
- Q10.4(a): Explain why (a) To keep a piece of paper horizontal, you should blow over, not under, it
- Q10.4(b): Explain why (b) When we try to close a water tap with our fingers, fast jets of water gush through the openings between our fingers
- Q10.4(c): Explain why (c) The size of the needle of a syringe controls flow rate better than the thumb pressure exerted by a doctor while administering an injection
- Q10.4(d): Explain why (d) A fluid flowing out of a small hole in a vessel results in a backward thrust on the vessel
- Q10.4(e): Explain why (e) A spinning cricket ball in air does not follow a parabolic trajectory
- Q10.5: A 50 kg girl wearing high heel shoes balances on a single heel. The heel is circular with a diameter 1.0 cm. What is the pressure exerted by the heel on the horizontal floor ?
- Q10.6: Toricelli’s barometer used mercury. Pascal duplicated it using French wine of density 984 $kg m^{-3}$. Determine the height of the wine column for normal atmospheric pressure.
- Q10.7: A vertical off-shore structure is built to withstand a maximum stress of $10^9$ Pa. Is the structure suitable for putting up on top of an oil well in the ocean ? Take the depth of the ocean to be roughly 3 km, and ignore ocean currents.
- Q10.8: A hydraulic automobile lift is designed to lift cars with a maximum mass of 3000 kg. The area of cross-section of the piston carrying the load is $425 cm^2$. What maximum pressure would the smaller piston have to bear ?
- Q10.9: A U-tube contains water and methylated spirit separated by mercury. The mercury columns in the two arms are in level with 10.0 cm of water in one arm and 12.5 cm of spirit in the other. What is the specific gravity of spirit ?
CBSE Solutions for Class 11 Physics Mechanical Properties of Fluids
Chapters in CBSE - Class 11 Physics
Top Tutors who teach Mechanical Properties of Fluids
Top Tutor
Narasapur, Gadag
10 yrs of
Exp
1 student
68 hrs of classes completed
400
per hour
Online Classes
I specialize in breaking down complex mathematical derivations, interpreting complex velocity-time or field graphs, and explaining the physical significance behind equations.Step-by-step algorithmic breakdown of complex integrals, visualizing 3D space geometries, and teaching the underlying logic of proofs.I break down intimidating, high-weightage topics into digestible sub-concepts. For example, before diving into complex Electromagnetic Induction problems, I ensure the student thoroughly grips Lenz's Law and magnetic flux concepts.
Top Tutor
Anora Kala, Lucknow
20 yrs of
Exp
2 students
2148 hrs of classes completed
400
per hour
Online Classes
Students enjoyed & learnt the subject. Programming in Java is thaught in a way that students understand the logic & also learn to apply it on similar problems. They fared well in various software competitions.
Very committed and focused on the concepts. My child benefited a lot with Mrs. Shilvanti's classes. Highly recommend using her as a tutor in case any child is facing challenges with Computers.
Top Tutor
Begur Road, Bangalore
5 yrs of
Exp
4 hrs of classes completed
350
per hour
Online Classes
Tutor's home
I have been teaching since last more than 5 years. My way of teaching style is so simple so that it make students very easier to understand. I am taking classes of Math and Hindi subject.
Top Tutor
Vaishali Nagar, Jaipur
9 yrs of
Exp
9 students
3087 hrs of classes completed
600
per hour
Online Classes
As a certified and top-ranked tutor on UrbanPro with over 9 years of teaching experience, I specialize in guiding Class 11 students as they transition into the commerce stream. My strength lies in simplifying complex Accountancy concepts and building a strong foundational understanding. Backed by 7+ years of industry experience in Accounting, Auditing, and Taxation, I effectively bridge theoretical learning with real-world application. My goal is to make learning engaging, practical, and confidence-boosting, helping students not only excel in exams but also prepare for higher studies in commerce.
He is good teacher for study. He teach detailly about subject. His teach style is strict. But sometimes this style is good for students.
Top Tutor
Sector 54 Suncity, Gurgaon
8 yrs of
Exp
1185 hrs of classes completed
800
per hour
Online Classes
Tutor's home
I have a varied experience of over 16 years and have enjoyed all roles as a writer, editor, banker, business analyst, teacher and marketer. I love a challenge, and during the course of my career, I took up English Language classes for working professionals. My classes are learner-centric and interactive, packed with activities, games and exercises that draw learners out of their shells and infuse them with confidence. Students are encouraged to think, raise questions, absorb new vocabulary and finally adopt the language as their own. My ability to connect and engage with students from all sections make my classes friendly, approachable and non-intimidating. My varied work experience across sectors further adds to my understanding of job and situation requirements.
Other Subjects in CBSE - Class 11
Download free CBSE - Class 11 Physics Mechanical Properties of Fluids EXERCISES worksheets
Download Now
