UrbanPro
true

Find the best tutors and institutes for Engineering Diploma Tuition

Find Best Engineering Diploma Tuition

Please select a Category.

Please select a Locality.

No matching category found.

No matching Locality found.

Outside India?

Search for topics

5 Basic Operations Of Lathe Machine

Rahul S
03/01/2018 0 0
(i) Facing: This operation is almost essential for all works. In this operation, as shown in fig., the work piece is held in the chuck and the facing tool is fed from the center of the work piece towards the outer surface or from the outer surface to the center, with the help of a cross-slide.
                                             

(ii) Plane Turning: It is an operation of removing excess amount of material from the surface the surface of the cylinder work piece. In this operation, shown in fig., the work is held either in the chuck or between centers & the longitudinal feed is given to the tool either by hand or power.
                                                          
  
(iii) Step Turning: It is an operation of producing various steps of different diameters of in the work piece as shown in fig. This operation is carried out in the similar way as plain turning.
 
                                                              
(iv) Drilling: It is an operation of making a hole in a work piece with the help of a drill. In this case as shown in fig., the work piece, by rotating the tail stock hand wheel. The drill is fed normally, into the rotating work piece, by rotating the tail stock hand wheel.
                                                          

(v) Reaming: It is an operation of finis hing the previously drilled hole. In the operation as shown in fig., a reamer is held in the tailstock and it is fed into the hole in the similar way as for drilling.
                                                
0 Dislike
Follow 3

Please Enter a comment

Submit

Other Lessons for You

Welding Defects - Causes and Remedies
DEFECTS IN WELDING (CAUSES) Improper welding parameter and wrong welding procedure introduce the welding defects in welded Joints. A defective welding Joint may fall under service condition and can...

Avantika P. | 01/04/2020

1 0
0

What Is VCR System?
VCR stands for Vapour Compression Refrigeration System. It is a refrigeration system in which cooling is obtained with the help of refrigerant. It consist of four major components such as Compressor, Condenser,...

Juned Kazi | 23/12/2017

0 0
0

Refrigeration Cycles & Its Applications
The term “refrigeration” is used to denote maintenance of a system or body at a temperature lower than that of its surroundings. The system maintained at the lower temperature is known as refrigerated...

Kamal Kumar | 06/07/2017

2 0
0

Saturated Steam Tables
A saturated steam table is an indispensable tool for any engineer working with steam. It's typically used to determine saturated steam temperature from steam pressure, or the opposite: pressure from saturated...

Kamal Kumar | 05/07/2017

3 0
1

Class - X Subject- Mathematics Chapter-Introduction to Trigonometry Assignment
If sinα =3/2, find the value of all T- ratios of α If cosα =7/25, find the value of all T-ratios of α If tanα =15/8, find the values of all T-ratios of α If cotα...

Rahul S | 16/04/2018

0 0
0

Looking for Engineering Diploma Tuition ?

Find best Engineering Diploma Tuition in your locality on UrbanPro.

Are you a Tutor or Training Institute?

Join UrbanPro Today to find students near you
Sponsored
X

Looking for Engineering Diploma Tuition Classes?

Find best tutors for Engineering Diploma Tuition Classes by posting a requirement.

  • Post a learning requirement
  • Get customized responses
  • Compare and select the best

Looking for Engineering Diploma Tuition Classes?

Find best Engineering Diploma Tuition Classes in your locality on UrbanPro

Post your learning requirement

UrbanPro.com is India's largest network of most trusted tutors and institutes. Over 55 lakh students rely on UrbanPro.com, to fulfill their learning requirements across 1,000+ categories. Using UrbanPro.com, parents, and students can compare multiple Tutors and Institutes and choose the one that best suits their requirements. More than 7.5 lakh verified Tutors and Institutes are helping millions of students every day and growing their tutoring business on UrbanPro.com. Whether you are looking for a tutor to learn mathematics, a German language trainer to brush up your German language skills or an institute to upgrade your IT skills, we have got the best selection of Tutors and Training Institutes for you. Read more