How does strain comes in a bar when it is fixed from both the ends? If strain is produced, does that mean the length of bar is increased when it is fixed?

Asked by Last Modified  

8 Answers

Follow 0
Answer

Please enter your answer

Rupa Intech Solutions

Driven By Innovation

It's neutral... No increase or decrease
Comments
Dislike Bookmark

GATE IES For Mechanical

If we talk about a bar with both end fixed, then strain never come. But there may be a stress for example if you give heat to a bar with both end fixed then compressible stress are there.
Comments
Dislike Bookmark

Former Scientist In DRDO

Because of bending moment stain introduced , length of bar increased , it bents by its own weight or applied load
Comments
Dislike Bookmark

Education is THE most important part of ones life, so embrace it and enjoy it.

Strain does not only depend on fixture. It depends on the type of load (i.e. tension, compression, torsion etc.) you are applying and accordingly you will see the strain. In universal testing machine (UTM), specimen is always fixed on both ends but the loading is tensile therefore, one observes axial...
read more
Strain does not only depend on fixture. It depends on the type of load (i.e. tension, compression, torsion etc.) you are applying and accordingly you will see the strain. In universal testing machine (UTM), specimen is always fixed on both ends but the loading is tensile therefore, one observes axial strain in specimen. Hope it'll clear your doubt, if not, contact me. read less
Comments
Dislike Bookmark

Mechanical Tutor

When the bar is fixed from both ends then strain of the bar should be zero.because in this case change in length is zero.and strain is change in length/original length
Comments
Dislike Bookmark

Tutor

In a bar fixed at both ends if we increase or decrease the temperature thermal stress will be induced as the elongation and contraction is restricted at both ends but there will be no thermal strain. Also there can be no tensile or compressive strain in the bar. But due to bending there can be strain...
read more
In a bar fixed at both ends if we increase or decrease the temperature thermal stress will be induced as the elongation and contraction is restricted at both ends but there will be no thermal strain. Also there can be no tensile or compressive strain in the bar. But due to bending there can be strain induced in the bar because in that case the length of the longitudinal fibres will change above and below the neutral fibre. read less
Comments
Dislike Bookmark

In my opinion, it can come, but then the assumption made in strength of material of homogeneous, isotropic and prismatic pair will be violated, and it may be because of change of shape due to bending moment.
Comments
Dislike Bookmark

As the bar has its own weight, when it is fixed on two sports the weight of the bar itself acts as a load to it. Eventually the bar experiences a little contraction in the lateral end and little expansion in the other surface.
Comments
Dislike Bookmark

View 6 more Answers

Related Questions

I am Shubham and my question is that I am an engineering student in 1st sem, so tell me study planning for the 1st Sem.
Since you're 1st semeter, just enjoy your college life with at least spend two hours to your studies. You should make a habit of thinking everything practically, try to understand whatever you study rather...
Shubhamparekh
How can I prepare for physical chemistry of class 12 without any coaching?
Physical chemistry, like any other stream of study, requires intricate interlinked study for proper understanding.For example,the concept of vapour pressure in the " solutions" chapter can be well fathomed...
Prabhu
0 0
View Comments6
Sir, I am doing diploma in mechanical branch. Now I want to do B.tech. Which entrance I should clear for admission?
Diploma CET.
Shanku
What is the Difference between Btech Software Engineering and BtechComputer Science Engineering at SRM University?
Hi, Difference only at academic level i.e. subject diffrence but at Organization there is no diffrence. All Engineers are equivilent at Organization i.e. Diploma Holders, B.Tech, BCA, MCA, B.Sc are equivally...
Meraj
0 0
View Comments5
Why density of Ice is lesser than water?
The main reason why the density of ice is lesser than that of water is because of its crystal structure. Four hydrogen atoms tetrahedrally surround each oxygen atom in the ice. Two of the hydrogen atoms...
Bitu

Now ask question in any of the 1000+ Categories, and get Answers from Tutors and Trainers on UrbanPro.com

Ask a Question

Related Lessons

Drag And Its Classifications
Introduction Drag is the enemy of flight and its cost. One group of those forces is aerodynamic forces that split into two forces: Lift force or lift, and Drag force or drag. A pre-requisite to aircraft...

Shivaji Batta

0 0
View Comments0
Transistors
A transistor can be used as a switch and signal amplifier. It is an electronic device with three contacts: the emitter (E), base (B) and collector (C). A very small current on the transistor's base can...

Shruthi H A

4 0
View Comments0
Organization And Architecture
In describing computers, a distinction is often made between computer architecture and computer organization. Although it is difficult to give precise definitions for these terms, a consensus exists about...

Harish Kumar

3 0
View Comments0
Brainmapping is the shortcut to longer subject recall.
Read through the subject matter and highlight the essential core areas covered. Select one core area at a time and dig into the finer details and subtopics,creating a brain map sequence. Write down...

Adeeba Riaz

0 0
View Comments0
Relevance Of Risk Mitigation & Disproportionate Collapse Control In India
Building Performance – Controlling Disproportionate CollapseThe importance of building structures has increased in the modern times due to the increasing complexity in the buildings due to increased...

Premjit Vasudevan

0 0
View Comments0

Recommended Articles

Tuitions for Professional courses - Does...

MBA, Medicine and engineering are the three main professional courses in India. Engineering is still one of the highly sorted after professional courses in the under graduate level, while MBA is favoured as a preferred post graduate course. To shine in these courses, one needs to work and study hard. Engineering as a...

Read full article >

Finding Tuitions for Bachelor of Engineering...

According to a recent survey conducted by the NCAER (National Council of Advanced Economic Research), engineering is the most sought after course in India. Some engineering courses are offered as BE or Bachelor of Engineering while some as Bachelor in Technology or B.Tech. Since engineering is a professional course, the...

Read full article >

6 Healthy Habits of School Children

While schools provide formal education to the children, the home is where they start learning about things informally. Parents think that schools will take the initiative to educate their children. Well, this is partially true, as parents also play an essential role in bringing up their child. For the development of particular...

Read full article >

Top Benefits of e-Learning

With the current trend of the world going digital, electronic renaissance is a new movement that is welcomed by the new generation as it helps makes the lives of millions of people easier and convenient. Along with this rapidly changing movement and gaining popularity of Internet, e-Learning is a new tool that emerging...

Read full article >

Find BTech Tuition near you
BTech Tuition in Hyderabad
BTech Tuition in Bangalore
BTech Tuition in Delhi
BTech Tuition in Chennai
BTech Tuition in Pune
BTech Tuition in Mumbai
BTech Tuition in Kolkata
BTech Tuition in Noida
BTech Tuition in Gurgaon
BTech Tuition in Ghaziabad
Online Btech Tuitions

Looking for BTech Tuition ?

Learn from the Best Tutors on UrbanPro

Are you a Tutor or Training Institute?

Join UrbanPro Today to find students near you