Find the best tutors and institutes for Class 11 Tuition
Q9.4(a):
Read the following two statements below carefully and state, with reasons, if it is true or false. (a) The Young’s modulus of rubber is greater than that of steel;
Solution :
Given Variables & Conceptual Foundation
To determine the validity of the statement "The Young’s modulus of rubber is greater than that of steel," we must refer to the definition of Young’s Modulus ($Y$):
$Y = \frac{\text{Stress}}{\text{Strain}} = \frac{F/A}{\Delta L/L}$
Where:
- $F$: Deforming force applied ($N$)
- $A$: Cross-sectional area ($m^2$)
- $L$: Original length ($m$)
- $\Delta L$: Change in length ($m$)
[Per the definition of Hooke's Law within the elastic limit, $Y$ represents the stiffness of a material. A higher value of $Y$ indicates that a material requires greater stress to produce a unit strain.]
Step 1: Comparative Analysis of Material Properties
We analyze the material response to an applied external stress:
| Material | Deformation Characteristic | Elastic Modulus ($Y$) |
|---|---|---|
| Rubber | High elongation for minimal force | Low ($Y \approx 0.01 - 0.1 \times 10^{10} \, \text{Pa}$) |
| Steel | Negligible elongation for significant force | High ($Y \approx 20 \times 10^{10} \, \text{Pa}$) |
Step 2: Logical Derivation
1. Observation: When an equal stress is applied to a wire of rubber and a wire of steel of identical dimensions, the rubber wire undergoes a significantly larger change in length ($\Delta L$) compared to the steel wire.
2. Mathematical Inference: Since $Y = \frac{\sigma}{\epsilon}$ (where $\sigma$ is stress and $\epsilon$ is strain), and for a given stress ($\sigma$), the strain ($\epsilon = \Delta L/L$) in rubber is much larger than the strain in steel:
$\epsilon_{\text{rubber}} \gg \epsilon_{\text{steel}}$
3. Conclusion: Because the denominator (strain) is much larger for rubber, the resulting value of $Y$ must be smaller for rubber than for steel.
Step 3: Visual Representation of Elasticity
Step 4: Final Evaluation of Statement
The statement is False. [Justification: Young’s Modulus is a measure of a material's resistance to elastic deformation. Steel is significantly more rigid than rubber, meaning it experiences much lower strain under the same load, resulting in a higher Young's Modulus value.]
Final Solution: The statement is False. The Young’s modulus of steel is significantly greater than that of rubber because steel is a more rigid material requiring higher stress to induce an equivalent strain compared to rubber.
More Questions from Class 11 Physics Mechanical Properties of Solids EXERCISES
- Q8.1: A steel wire of length 4.7 m and cross-sectional area \(3.0 \times 10^{-5} \text{ m}^{2}\) stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of \(4.0 \times 10^{–5} \text{ m}^{2}\) under a given load. What is the ratio of the Young’s modulus of steel to that of copper?
- Q8.10: A rigid bar of mass 15 kg is supported symmetrically by three wires each 2.0 m long. Those at each end are of copper and the middle one is of iron. Determine the ratios of their diameters if each is to have the same tension.
- Q8.11: A 14.5 kg mass, fastened to the end of a steel wire of unstretched length 1.0 m, is whirled in a vertical circle with an angular velocity of 2 rev/s at the bottom of the circle. The cross-sectional area of the wire is \(0.065 \text{ cm}^{2}\). Calculate the elongation of the wire when the mass is at the lowest point of its path.
- Q8.12: Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre, Pressure increase = 100.0 atm (\(1 \text{ atm} = 1.013 \times 10^{5} \text{ Pa}\)), Final volume = 100.5 litre. Compare the bulk modulus of water with that of air (at constant temperature). Explain in simple terms why the ratio is so large.
- Q8.13: What is the density of water at a depth where pressure is 80.0 atm, given that its density at the surface is \(1.03 \times 10^{3} \text{ kg m}^{–3}\)?
- Q8.14: Compute the fractional change in volume of a glass slab, when subjected to a hydraulic pressure of 10 atm.
- Q8.15: Determine the volume contraction of a solid copper cube, 10 cm on an edge, when subjected to a hydraulic pressure of \(7.0 \times 10^{6} \text{ Pa}\).
- Q8.16: How much should the pressure on a litre of water be changed to compress it by 0.10%? carry one quarter of the load.
- Q8.2 (a): Figure 8.9 shows the strain-stress curve for a given material. What are (a) Young’s modulus for this material?
- Q8.2 (b): Figure 8.9 shows the strain-stress curve for a given material. What are (b) approximate yield strength for this material?
- Q8.3 (a): The stress-strain graphs for materials A and B are shown in Fig. 8.10. The graphs are drawn to the same scale. (a) Which of the materials has the greater Young’s modulus?
- Q8.3 (b): The stress-strain graphs for materials A and B are shown in Fig. 8.10. The graphs are drawn to the same scale. (b) Which of the two is the stronger material?
- Q8.4 (a): Read the following two statements below carefully and state, with reasons, if it is true or false. (a) The Young’s modulus of rubber is greater than that of steel;
- Q8.4 (b): Read the following two statements below carefully and state, with reasons, if it is true or false. (b) The stretching of a coil is determined by its shear modulus.
- Q8.5: Two wires of diameter 0.25 cm, one made of steel and the other made of brass are loaded as shown in Fig. 8.11. The unloaded length of steel wire is 1.5 m and that of brass wire is 1.0 m. Compute the elongations of the steel and the brass wires.
- Q8.6: The edge of an aluminium cube is 10 cm long. One face of the cube is firmly fixed to a vertical wall. A mass of 100 kg is then attached to the opposite face of the cube. The shear modulus of aluminium is 25 GPa. What is the vertical deflection of this face?
- Q8.7: Four identical hollow cylindrical columns of mild steel support a big structure of mass 50,000 kg. The inner and outer radii of each column are 30 and 60 cm respectively. Assuming the load distribution to be uniform, calculate the compressional strain of each column.
- Q8.8: A piece of copper having a rectangular cross-section of \(15.2 \text{ mm} \times 19.1 \text{ mm}\) is pulled in tension with 44,500 N force, producing only elastic deformation. Calculate the resulting strain?
- Q8.9: A steel cable with a radius of 1.5 cm supports a chairlift at a ski area. If the maximum stress is not to exceed \(10^{8} \text{ N m}^{–2}\), what is the maximum load the cable can support ?
- Q9.1: A steel wire of length 4.7 m and cross-sectional area $3.0 \times 10^{-5} m^2$ stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of $4.0 \times 10^{-5} m^2$ under a given load. What is the ratio of the Young’s modulus of steel to that of copper?
- Q9.10: A rigid bar of mass 15 kg is supported symmetrically by three wires each 2.0 m long. Those at each end are of copper and the middle one is of iron. Determine the ratios of their diameters if each is to have the same tension.
- Q9.11: A 14.5 kg mass, fastened to the end of a steel wire of unstretched length 1.0 m, is whirled in a vertical circle with an angular velocity of 2 rev/s at the bottom of the circle. The cross-sectional area of the wire is $0.065 \text{ cm}^2$. Calculate the elongation of the wire when the mass is at the lowest point of its path.
- Q9.12: Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre, Pressure increase = 100.0 atm (1 atm = $1.013 \times 10^5$ Pa), Final volume = 100.5 litre. Compare the bulk modulus of water with that of air (at constant temperature). Explain in simple terms why the ratio is so large.
- Q9.13: What is the density of water at a depth where pressure is 80.0 atm, given that its density at the surface is $1.03 \times 10^3 \text{ kg m}^{-3}$?
- Q9.14: Compute the fractional change in volume of a glass slab, when subjected to a hydraulic pressure of 10 atm.
- Q9.15: Determine the volume contraction of a solid copper cube, 10 cm on an edge, when subjected to a hydraulic pressure of $7.0 \times 10^6$ Pa.
- Q9.16: How much should the pressure on a litre of water be changed to compress it by 0.10%?
- Q9.2(a): Figure 9.11 shows the strain-stress curve for a given material. What are (a) Young’s modulus for this material?
- Q9.2(b): Figure 9.11 shows the strain-stress curve for a given material. What are (b) approximate yield strength for this material?
- Q9.3(a): The stress-strain graphs for materials A and B are shown in Fig. 9.12. The graphs are drawn to the same scale. (a) Which of the materials has the greater Young’s modulus?
- Q9.3(b): The stress-strain graphs for materials A and B are shown in Fig. 9.12. The graphs are drawn to the same scale. (b) Which of the two is the stronger material?
- Q9.4(b): Read the following two statements below carefully and state, with reasons, if it is true or false. (b) The stretching of a coil is determined by its shear modulus.
- Q9.5: Two wires of diameter 0.25 cm, one made of steel and the other made of brass are loaded as shown in Fig. 9.13. The unloaded length of steel wire is 1.5 m and that of brass wire is 1.0 m. Compute the elongations of the steel and the brass wires.
- Q9.6: The edge of an aluminium cube is 10 cm long. One face of the cube is firmly fixed to a vertical wall. A mass of 100 kg is then attached to the opposite face of the cube. The shear modulus of aluminium is 25 GPa. What is the vertical deflection of this face?
- Q9.7: Four identical hollow cylindrical columns of mild steel support a big structure of mass 50,000 kg. The inner and outer radii of each column are 30 and 60 cm respectively. Assuming the load distribution to be uniform, calculate the compressional strain of each column.
- Q9.8: A piece of copper having a rectangular cross-section of $15.2 \text{ mm} \times 19.1 \text{ mm}$ is pulled in tension with 44,500 N force, producing only elastic deformation. Calculate the resulting strain?
- Q9.9: A steel cable with a radius of 1.5 cm supports a chairlift at a ski area. If the maximum stress is not to exceed $10^8 \text{ N m}^{-2}$, what is the maximum load the cable can support ?
CBSE Solutions for Class 11 Physics Mechanical Properties of Solids
Chapters in CBSE - Class 11 Physics
Top Tutors who teach Mechanical Properties of Solids
Top Tutor
Medchal, Hyderabad
8 yrs of
Exp
9 students
1982 hrs of classes completed
Online Classes
Students are used to listen each and every lecture carefully n practically too. I teach them theory part by taking examples. Doing more practice sessions so that their logical part will get more clear. Online teaching provides 1. Personal attention to each and every student. 2. Their practical session always b free of doubts. 3. Online classes provide teachers with a number of online learning tools including videos, audio, animations, virtual whiteboards. 4. Time to time notes will b provided
Top Tutor
Hiran Magri Sector 14, Udaipur
7 yrs of
Exp
73 students
3805 hrs of classes completed
400
per hour
Online Classes
I am a home tutor I teach since 2016. my teaching style is easy and impactful I use examples and mostly I use the questioner method mostly I used linear questions for learning. and I teach you how to prepare a short note in an effective way and how to convert your short not learning into easy type answers and i promise you as a tutor the whole procdure you will enjoy.
I’m really thankful to my TTN accounts teacher for the way they teach. Accounts can feel confusing at times, but the way every topic is explained so clearly makes it much easier to understand. They always start from the basics and make sure everyone is on the same page before moving ahead. Doubts are never ignored, and the examples given in class actually help things make sense. Because of their teaching, my confidence in accounts has improved a lot. It honestly feels easier and less stressful to study the subject now.
Top Tutor
Kamal Chowk, Nagpur
20 yrs of
Exp
2 hrs of classes completed
Tutor's home
I have 20 years of experience in the field of teaching. I conduct classes for Spoken English, BBA, MBA, Hindi Language, Career Counselling and Classes I to X. I tutor (offline/online) for syllabi-based subjects Classes I to X for CBSE, ICSE, IGCSE, IB Board. For classes X and above, I focus on tutoring subjects like Hindi, English, Psychology. Accountancy, Business Studies, Mathematics, Physics, Chemistry for CBSE, ICSE, IGCSE and IB Board. I also conduct career counselling and psychological counselling. I also assist students in pursuing MBA/PGDBM courses in their dissertation work. People engaged in doctoral theses in the domains of management and psychology engage my services for their research work. Since there is a lot of demand for enhancing one's conversational English, this is what I am focusing on at the moment. Being bilingual, my medium of communication is English as well as Hindi. I train learners in the usage of WordPress, Joomla - to develop their websites; right from domain registration to site maintenance. Besides, I assist teachers in pursuing Teachers' Training Courses.
Super Tutor
New Friends Colony, Delhi
10 yrs of
Exp
30 students
4691 hrs of classes completed
500
per hour
Online Classes
I help students in Classes 11–12 develop strong conceptual understanding, advanced problem-solving skills, and confidence for school, board, and competitive-level examinations. My classes cover: Algebra – equations, sequences & series, permutations & combinations, binomial theorem, complex numbers, etc. Trigonometry – identities, equations and applications Coordinate Geometry – straight lines, circles and conic sections Calculus – limits, continuity, differentiation, applications of derivatives, integration and related concepts Probability & Statistics Vectors & 3D Geometry Matrices & Determinants Application-based and higher-order problems Regular practice, tests, and detailed error analysis Exam-oriented preparation with focus on accuracy, speed, and time management My Teaching Approach Instead of simply teaching formulas, I focus on helping students understand why a concept works, when to apply it, and how to approach unfamiliar questions. Concept → Understand → Practise → Apply → Solve → Analyse → Improve Classes are personalised according to the student's current level, curriculum, learning gaps, and academic goals, with structured practice and continuous feedback. Suitable for: CBSE, ICSE, IB, IGCSE, GCSE, Cambridge, and other international curricula.
The teacher explained concepts with simple examples and experiments, which made learning easy and interesting I understood the topic better and improved my performance .
Top Tutor
Choolissery, Thrissur
20 yrs of
Exp
1 student
446 hrs of classes completed
600
per hour
Online Classes
Very simple and easy to learn
Other Subjects in CBSE - Class 11
Download free CBSE - Class 11 Physics Mechanical Properties of Solids EXERCISES worksheets
Download Now
