Find the best tutors and institutes for Class 11 Tuition
Mechanical Properties of Solids EXERCISES Solutions
- Q8.1: A steel wire of length 4.7 m and cross-sectional area \(3.0 \times 10^{-5} \text{ m}^{2}\) stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of \(4.0 \times 10^{–5} \text{ m}^{2}\) under a given load. What is the ratio of the Young’s modulus of steel to that of copper?
- Q8.10: A rigid bar of mass 15 kg is supported symmetrically by three wires each 2.0 m long. Those at each end are of copper and the middle one is of iron. Determine the ratios of their diameters if each is to have the same tension.
- Q8.11: A 14.5 kg mass, fastened to the end of a steel wire of unstretched length 1.0 m, is whirled in a vertical circle with an angular velocity of 2 rev/s at the bottom of the circle. The cross-sectional area of the wire is \(0.065 \text{ cm}^{2}\). Calculate the elongation of the wire when the mass is at the lowest point of its path.
- Q8.12: Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre, Pressure increase = 100.0 atm (\(1 \text{ atm} = 1.013 \times 10^{5} \text{ Pa}\)), Final volume = 100.5 litre. Compare the bulk modulus of water with that of air (at constant temperature). Explain in simple terms why the ratio is so large.
- Q8.13: What is the density of water at a depth where pressure is 80.0 atm, given that its density at the surface is \(1.03 \times 10^{3} \text{ kg m}^{–3}\)?
- Q8.14: Compute the fractional change in volume of a glass slab, when subjected to a hydraulic pressure of 10 atm.
- Q8.15: Determine the volume contraction of a solid copper cube, 10 cm on an edge, when subjected to a hydraulic pressure of \(7.0 \times 10^{6} \text{ Pa}\).
- Q8.16: How much should the pressure on a litre of water be changed to compress it by 0.10%? carry one quarter of the load.
- Q8.2 (a): Figure 8.9 shows the strain-stress curve for a given material. What are (a) Young’s modulus for this material?
- Q8.2 (b): Figure 8.9 shows the strain-stress curve for a given material. What are (b) approximate yield strength for this material?
- Q8.3 (a): The stress-strain graphs for materials A and B are shown in Fig. 8.10. The graphs are drawn to the same scale. (a) Which of the materials has the greater Young’s modulus?
- Q8.3 (b): The stress-strain graphs for materials A and B are shown in Fig. 8.10. The graphs are drawn to the same scale. (b) Which of the two is the stronger material?
- Q8.4 (a): Read the following two statements below carefully and state, with reasons, if it is true or false. (a) The Young’s modulus of rubber is greater than that of steel;
- Q8.4 (b): Read the following two statements below carefully and state, with reasons, if it is true or false. (b) The stretching of a coil is determined by its shear modulus.
- Q8.5: Two wires of diameter 0.25 cm, one made of steel and the other made of brass are loaded as shown in Fig. 8.11. The unloaded length of steel wire is 1.5 m and that of brass wire is 1.0 m. Compute the elongations of the steel and the brass wires.
- Q8.6: The edge of an aluminium cube is 10 cm long. One face of the cube is firmly fixed to a vertical wall. A mass of 100 kg is then attached to the opposite face of the cube. The shear modulus of aluminium is 25 GPa. What is the vertical deflection of this face?
- Q8.7: Four identical hollow cylindrical columns of mild steel support a big structure of mass 50,000 kg. The inner and outer radii of each column are 30 and 60 cm respectively. Assuming the load distribution to be uniform, calculate the compressional strain of each column.
- Q8.8: A piece of copper having a rectangular cross-section of \(15.2 \text{ mm} \times 19.1 \text{ mm}\) is pulled in tension with 44,500 N force, producing only elastic deformation. Calculate the resulting strain?
- Q8.9: A steel cable with a radius of 1.5 cm supports a chairlift at a ski area. If the maximum stress is not to exceed \(10^{8} \text{ N m}^{–2}\), what is the maximum load the cable can support ?
- Q9.1: A steel wire of length 4.7 m and cross-sectional area $3.0 \times 10^{-5} m^2$ stretches by the same amount as a copper wire of length 3.5 m and cross-sectional area of $4.0 \times 10^{-5} m^2$ under a given load. What is the ratio of the Young’s modulus of steel to that of copper?
- Q9.10: A rigid bar of mass 15 kg is supported symmetrically by three wires each 2.0 m long. Those at each end are of copper and the middle one is of iron. Determine the ratios of their diameters if each is to have the same tension.
- Q9.11: A 14.5 kg mass, fastened to the end of a steel wire of unstretched length 1.0 m, is whirled in a vertical circle with an angular velocity of 2 rev/s at the bottom of the circle. The cross-sectional area of the wire is $0.065 \text{ cm}^2$. Calculate the elongation of the wire when the mass is at the lowest point of its path.
- Q9.12: Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre, Pressure increase = 100.0 atm (1 atm = $1.013 \times 10^5$ Pa), Final volume = 100.5 litre. Compare the bulk modulus of water with that of air (at constant temperature). Explain in simple terms why the ratio is so large.
- Q9.13: What is the density of water at a depth where pressure is 80.0 atm, given that its density at the surface is $1.03 \times 10^3 \text{ kg m}^{-3}$?
- Q9.14: Compute the fractional change in volume of a glass slab, when subjected to a hydraulic pressure of 10 atm.
- Q9.15: Determine the volume contraction of a solid copper cube, 10 cm on an edge, when subjected to a hydraulic pressure of $7.0 \times 10^6$ Pa.
- Q9.16: How much should the pressure on a litre of water be changed to compress it by 0.10%?
- Q9.2(a): Figure 9.11 shows the strain-stress curve for a given material. What are (a) Young’s modulus for this material?
- Q9.2(b): Figure 9.11 shows the strain-stress curve for a given material. What are (b) approximate yield strength for this material?
- Q9.3(a): The stress-strain graphs for materials A and B are shown in Fig. 9.12. The graphs are drawn to the same scale. (a) Which of the materials has the greater Young’s modulus?
- Q9.3(b): The stress-strain graphs for materials A and B are shown in Fig. 9.12. The graphs are drawn to the same scale. (b) Which of the two is the stronger material?
- Q9.4(a): Read the following two statements below carefully and state, with reasons, if it is true or false. (a) The Young’s modulus of rubber is greater than that of steel;
- Q9.4(b): Read the following two statements below carefully and state, with reasons, if it is true or false. (b) The stretching of a coil is determined by its shear modulus.
- Q9.5: Two wires of diameter 0.25 cm, one made of steel and the other made of brass are loaded as shown in Fig. 9.13. The unloaded length of steel wire is 1.5 m and that of brass wire is 1.0 m. Compute the elongations of the steel and the brass wires.
- Q9.6: The edge of an aluminium cube is 10 cm long. One face of the cube is firmly fixed to a vertical wall. A mass of 100 kg is then attached to the opposite face of the cube. The shear modulus of aluminium is 25 GPa. What is the vertical deflection of this face?
- Q9.7: Four identical hollow cylindrical columns of mild steel support a big structure of mass 50,000 kg. The inner and outer radii of each column are 30 and 60 cm respectively. Assuming the load distribution to be uniform, calculate the compressional strain of each column.
- Q9.8: A piece of copper having a rectangular cross-section of $15.2 \text{ mm} \times 19.1 \text{ mm}$ is pulled in tension with 44,500 N force, producing only elastic deformation. Calculate the resulting strain?
- Q9.9: A steel cable with a radius of 1.5 cm supports a chairlift at a ski area. If the maximum stress is not to exceed $10^8 \text{ N m}^{-2}$, what is the maximum load the cable can support ?
Chapters in CBSE - Class 11 Physics
Top Tutors who teach Mechanical Properties of Solids
Super Tutor 
Mulund East, Mumbai 
20 yrs of Exp 
6 students 
598 hrs of classes completed 
1500 per hour 
Online Classes 
Student's Home 
Tutor's home I have been teaching students for the last 20 years. Many of my students had passed with more than 95% marks or higher grade. I always love interactive classes so always motivate my students to ask as many questions as they can.Once the teaching process becomes dialogue from monologue then I understand that half of the task has been done and thereafter concept building process becomes very easy as I constantly guided by the questions from my students. Keeping class regularly on time, solving questions everyday, clearing doubts on a regular basis and lastly keeping weekly test make it very simple to make a good score.
His teaching methods are great. Very clear and concise. Always lectures with the intent to help you understand the material. He’s helped me understand content for chemistry and is one of the best teacher that I’ve had. Recommending her/him is a no brainer.
Super Tutor Knowledge Park II, Noida 8 yrs of Exp 351 students 65944 hrs of classes completed 400 per hour Online Classes I have been teaching students since past 8 years and in this journey many of them were able to crack their examination.My way of teaching makes approach towards the question more simpler and easier.If you feel jee is not yours cup of tea then trust me once I will make sure you will start feeling damn comfort and your way of thinking will definitely change Not just only education I teach my students about life values as cracking examination is combo of disciplne, determination,hardwordk and little luck so just doing solving any question never tends to success. All these qualities must get inbuilt.
Excellent classes. Sir is extremely enthusiastic and always ready to help. He provides all levels of notes and gives the freedom to students to choose. He is the super star teacher for physics and chemistry. Praying that tye enthusiasm persists. Thank you Sir.
Top Tutor Vesu, Surat 20 yrs of Exp 16 students 2476 hrs of classes completed 500 per hour Online Classes I have experience teaching Mathematics to Grade 11 students with a focus on building a strong foundation for higher-level mathematics. I teach important topics such as Sets, Relations and Functions, Trigonometry, Complex Numbers, Quadratic Equations, Permutations and Combinations, Binomial Theorem, and Coordinate Geometry. My teaching method emphasizes clear explanation of concepts, step-by-step problem solving, and regular practice. I use examples from NCERT and previous exam questions to strengthen students’ understanding. I also conduct periodic tests and revision sessions to monitor progress and clear doubts. My aim is to develop logical thinking, improve problem-solving ability, and prepare students effectively for Grade 12 mathematics.
Extremely beneficial classes. Virendra sir explains every topic in an easy to understand manner and starts the practice of questions from ncert to higher level.
Super Tutor Okkiyam Thuraipakkam, Chennai 5 yrs of Exp 14 students 892 hrs of classes completed 300 per hour Online Classes I have taught online for almost 5 years in Economics for class XI students, both for CBSE and ISC/ICSE. I have been giving 1:1 and group classes to the students. My students have always enjoyed learning with me and have achieved their best. First of all of my students start loving the subject as well as gain confidence in themselves. I feel encouraged to teach more by the feedbacks and the excellent results by my students. Almost all of them continue learning with me in class 12 as well. Further in 12 I give complete preparation for board exam.
Great tutoring experience, syllabus is completed and revision has already started a month before final examination.
Top Tutor Periyakollappatty, Salem 6 yrs of Exp 5 students 131 hrs of classes completed Online Classes Student's Home Tutor's home I can teach every topic very easily and make it stronger for the students.
Other Subjects in CBSE - Class 11
Download free CBSE - Class 11 Physics Mechanical Properties of Solids EXERCISES worksheets
Download Now
